Chamber reamers – HANZ Arms

Accessories · Gunsmithing tools

Chamber reamers

HANZ Arms makes gunsmithing tools for gunsmiths, workshops and barrel makers. The range covers solid-carbide chamber reamers cut to CIP spec – on request to CIP minimum – along with a chamber roughing drill, throating reamers and brass pilot bushings. We make your carbide reamer for any caliber you need and deliver within 14 days.


01 / Tools

Solid-carbide chamber reamers from HANZ Arms.

We make our chamber reamers from solid carbide and use them ourselves when building our long-range rifles. The same tools that prove themselves in our own workshop are available for your work as a gunsmith, workshop or barrel maker – for the caliber you need, cut to CIP spec and, on request, to CIP minimum.







02 / Why HANZ Arms

Tools from real-world use.


  • Machined from a solid carbide blank – uncoated
  • Geometry to CIP spec, on request to CIP minimum for the tightest tolerances
  • Any caliber you need – tell us the caliber and your tolerance preference
  • Made within 14 days
  • Proven in our own gunsmithing shop: every HANZ Arms long-range rifle gets its chamber cut with these reamers
  • Order directly in the Das Waffengeschäft online shop or by enquiry with caliber and tolerance preference



At a glance

Material
Solid carbide
Standard
CIP spec, optional CIP minimum
Caliber
any caliber on request
Delivery
approx. 14 days
Accessories
roughing drill, throating reamer, pilot bushings (set of three)
Manufacturer
HANZ Arms, Austria





03 / Questions & answers

Common questions about gunsmithing tools and reamers.

Answers about HANZ Arms gunsmithing tools: from carbide reamers and CIP minimum through the chamber roughing drill to throating reamers and pilot bushings.



HANZ Arms and our technical approach

What sets HANZ Arms gunsmithing tools apart?

HANZ Arms gunsmithing tools are engineered for the needs of gunsmiths, workshops and barrel makers. The range covers finishing reamers, complete reamers, throating reamers, chamber roughing drills and brass pilot bushings. We use the reamers ourselves when building our long-range rifles.

Which tools are in the HANZ Arms range?

Our range covers finishing reamers without throating cone, complete reamers with throating cone and throating reamers, plus chamber roughing drills and brass pilot bushings. In our method the roughing drill combines the jobs of roughing and pre-finishing reamers. When ordering, state the tool type and version you need explicitly.

Who are the tools for?

HANZ Arms gunsmithing tools are intended for gunsmiths, workshops and barrel makers. The focus is on tools for chamber work and the matching accessories. For an enquiry, give the caliber you need and the tool type required.

Where is HANZ Arms based?

HANZ Arms belongs to Hanz GmbH in Austria. We develop and make our tools in-house and with regional partner shops. You will find current contact details and the address on our contact page.

Does HANZ Arms use these reamers itself?

Yes. We cut the chambers of our own long-range rifles with these chamber reamers. So you get tools we use ourselves in our gunsmithing shop. Our product descriptions are based on that first-hand use.

Why does HANZ Arms prefer complete reamers in daily work?

In everyday gunsmithing we prefer complete reamers because they finish the chamber including the throating cone in a single step. The throat does not need a separate tool. We use these tools ourselves when building our long-range rifles.


Chamber reamers and complete reamers

What is a chamber reamer?

Chamber reamer is the umbrella term for reamers used to work the chamber. It covers different tool types: a finishing reamer finishes the chamber without a throating cone; a complete reamer includes the throating cone. HANZ Arms supplies both versions. State the reamer type you want when ordering.

What material are HANZ Arms chamber reamers made of?

Our chamber reamers are made of solid carbide. The tool body is machined from a carbide blank. The material refers to the reamer; the interchangeable pilot bushings are brass.

What is the difference between carbide and HSS reamers?

Carbide and HSS are different tool materials. Carbide offers high wear resistance; HSS stands for high-speed steel and is tougher. HANZ Arms offers the chamber reamers described here in solid carbide. No universal tool-life figure can be derived from this.

What is the difference between a finishing reamer and a complete reamer?

A finishing reamer works the chamber without a throating cone; the throat is then cut separately with a throating reamer. A complete reamer has the throating cone integrated and cuts chamber and throat together during finish-reaming. HANZ Arms supplies both tool types; state the version you want explicitly when ordering.

Do the chamber reamers have an interchangeable pilot bushing?

Yes. HANZ Arms chamber reamers have an interchangeable pilot bushing that centers the reamer in the bore. The brass pilot bushing is a separate accessory and can be replaced without replacing the whole reamer.

How long does a chamber reamer last?

A chamber reamer’s tool life depends on the barrel-steel material being cut, the lubrication, the operating conditions and the condition of the tool. So no fixed number of chambers can be stated for every application. The HANZ chamber roughing drill relieves the reamer by taking over the roughing work.


CIP spec and tool versions

What does CIP mean for chamber reamers?

CIP is the international commission for the proof of small arms. Its dimension tables set out specifications for cartridges and chambers. The HANZ Arms chamber reamers described here conform to the CIP spec for the respective caliber.

Are reamers available to CIP minimum?

Yes. HANZ Arms supplies chamber reamers to CIP minimum on request. If you need this version, state it explicitly in your enquiry so it is clear which version should be offered for your caliber.

Are CIP minimum and tighter manufacturing tolerances the same thing?

No. CIP minimum refers to a dimensional specification. Manufacturing tolerances describe the permissible deviation from a given dimension. The terms mean different things. A CIP-minimum reamer is therefore not automatically the same as tighter tolerances in its manufacture.

Does CIP minimum guarantee higher accuracy?

A CIP-minimum chamber is not, in itself, a guarantee of higher accuracy. The term describes the dimensional basis of the reamer. No blanket accuracy gain for every rifle can be derived from it.

Which version does HANZ Arms recommend for semi-automatics?

For semi-automatics we recommend the standard version to CIP spec. We advise against the minimum version for this use. State in your enquiry that the tool is intended for a semi-automatic so the version can be recorded unambiguously.

What is the difference between CIP and SAAMI?

CIP and SAAMI are different organisations, each with its own technical standards and publications on cartridges and chambers. The same caliber name therefore does not replace stating the standard basis you want. The reamer range described here follows CIP spec.

Where do I find the official CIP dimension tables?

CIP publishes its official tables for cartridges and chambers as the TDCC on its website. TDCC stands for Tables of Dimensions of Cartridges and Chambers. For matching a tool, the exact caliber designation and the agreed version are decisive.


Chamber roughing drill and machining time

What does the HANZ Arms chamber roughing drill do?

The HANZ Arms chamber roughing drill opens the chamber contour 0.3 mm undersize. It combines the jobs of roughing and pre-finishing reamers in one tool. Pre-drilling saves machining time, because in our method drilling is faster than reaming, and it spares the reamer during the subsequent finish-reaming.

What is the advantage of pre-drilling over a three-stage reaming sequence?

With the HANZ tool concept described here, two steps are enough: roughing-drill, then finish-ream with the complete reamer including throating cone. The roughing drill combines the jobs of roughing and pre-finishing reamers. Compared with a three-stage reaming sequence, one step is eliminated. With this complete version, separate work on the throat is not required.

Why does the chamber roughing drill save machining time?

The time advantage comes from the drilled roughing, which in the HANZ method described is faster than the equivalent roughing by reaming. The complete reamer then does the finish-reaming. A fixed time saving in minutes or percent depends on the particular application.

Why does the roughing drill spare the complete reamer?

The roughing drill takes over the material removal before finish-reaming. As a result the complete reamer has to remove less material and is relieved. The reduced wear comes from this division of labour between contour roughing drill and chamber reamer.

What does the three-tenths undersize on the HANZ roughing drill mean?

Three tenths here means 0.3 mm undersize relative to the intended finished contour. The roughing drill takes over the roughing that, in a three-stage reaming sequence, is split between roughing and pre-finishing reamers. Finish-reaming remains the job of the finishing or complete reamer.

Does HANZ Arms supply roughing and pre-finishing reamers?

No. Roughing and pre-finishing reamers are not part of our range. Their roughing jobs are combined in our chamber roughing drill, in one tool. For the subsequent finish-reaming, HANZ Arms offers finishing reamers without throating cone or complete reamers with throating cone.


Throating reamers and the bullet leade

What is a throating reamer for?

The HANZ Arms throating reamer, also called a throating-cone reamer, cuts the bullet leade separately. It is needed when the chamber has been worked with a finishing reamer without an integrated throating cone. Headspace and case neck stay unchanged.

Does the throating reamer change headspace or the case neck?

No. The throating reamer described here works the bullet leade only. Its tool function is separate from working the headspace and case neck. That sets it apart from tool versions that work several areas together.

When is an additional throating-cone reamer needed?

After working with a finishing reamer without a throating cone, the throat is cut separately with a throating-cone reamer. With a complete reamer the throating cone is already part of the tool and is cut during finish-reaming. For this complete machining, no extra operation to cut the throat is required.

What is the advantage of working the bullet leade separately?

When using a finishing reamer without a throating cone, the throat can be cut separately afterwards with a throating-cone reamer. The throat depth can thereby be set independently of the finishing reamer and matched to the intended bullet and its seating depth. Headspace and case neck stay unchanged.

Does HANZ Arms use another name for the throating reamer?

HANZ Arms calls this tool the Übergangsreibahle in German; in the international tool trade, terms like throating reamer or throater reamer are used. With international offers the specific product description matters, because combined tools can cover different machining areas.


Pilot bushings and chip removal

What do pilot bushings do for reamers?

HANZ Arms pilot bushings center the reamer in the bore. They are made of brass and are interchangeable. Bushing and reamer do different jobs: the bushing provides the guidance, the reamer does the cutting.

Why are the pilot bushings made of brass?

HANZ Arms uses brass for the pilot bushings described here because the comparatively soft material protects the rifling. The bushings support centering of the reamer in the bore and can be replaced when needed.

What are the spiral grooves in the pilot bushings for?

The spiral-milled grooves allow high-pressure lubrication fed from the muzzle, through the barrel. They provide a flow path for the lubricant around the pilot bushing. This lets the lubricant flush the chips rearward, out of the chamber.

Which direction are the chips carried during lubrication through the barrel?

In the HANZ system described here, the lubricant is fed from the muzzle, through the barrel. The chips are flushed rearward, out of the chamber. The direction of chip removal is thus front to back.

Why is chip removal a distinct advantage of the pilot bushings?

The spiral grooves add a flow path for the lubricant to the guiding function. The pilot bushing centers the reamer; the lubricant flowing through supports carrying the chips out of the chamber. So the HANZ pilot bushings combine centering with the chip removal described.

Are the brass pilot bushings interchangeable?

Yes. HANZ Arms brass pilot bushings are easy to change. The bushing can be swapped as an accessory while the reamer stays in use. The right version depends on the particular tool.

In what combination are the pilot bushings offered?

HANZ Arms offers the pilot bushings described here in a set of three. The set consists of three brass pilot bushings. State the matching reamer and caliber in your enquiry so the set you need can be assigned unambiguously.


Caliber and delivery time

For which calibers are HANZ Arms chamber reamers available?

At HANZ Arms you can get the finishing, complete and throating reamers described for any caliber you need. When ordering, give the full caliber designation, the reamer type you want and the dimensional version. State explicitly whether you need a finishing reamer without throating cone, a complete reamer with throating cone or a throating reamer. For roughing we offer chamber roughing drills.

How quickly does HANZ Arms deliver carbide reamers?

We deliver the carbide reamers described within 14 days. We confirm the specific delivery date as part of your enquiry. Any additional services or accessories are arranged separately.

Does the 14-day delivery apply to all accessories too?

The 14-day figure refers to the carbide reamers described. The delivery time for an accessory or another tool item cannot automatically be derived from it. List all the items you need in your enquiry so their availability can be clarified together.


Service, versions & shipping

Do you offer a regrinding service for reamers?

Yes, for our own reamers – except for tools made to CIP minimum. Price on request, turnaround around 14 days.

Do you also regrind reamers from other makers?

No, we do not work on third-party tools.

Is every reamer inspected?

Every tool goes through an internal inspection. We supply a measurement report on request for a surcharge.

Is there a dimensional drawing for every reamer?

Dimensional drawings exist but are not supplied with the tool. We can add a measurement report to any reamer for a surcharge.

Do you also make to SAAMI?

As standard we make to CIP spec. We make to SAAMI on request – state this explicitly in your enquiry.

Are the reamers coated?

As standard we supply our tools uncoated. On request every tool is also available titanium-nitride coated (TiN).

Do you offer headspace gauges (go/no-go)?

We already make special orders; ex-stock go/no-go gauges will be available shortly.

Are there minimum quantities or discounts?

There is no minimum quantity. Discounts apply when ordering several identical tools at once.

How quickly can you deliver, is there an express option?

Stock items are available quickly; special orders take correspondingly longer – we agree the date in the specific case. Express is possible, but only on prior enquiry.

Do you ship abroad?

Yes, we ship worldwide. We clarify any necessary permits in advance with the destination country.


Enquiry and technical contact

What belongs in a tool enquiry?

Give the tool type you want, the full caliber designation and the quantity needed. Distinguish explicitly between finishing reamer without throating cone, complete reamer with throating cone, throating reamer and chamber roughing drill. For reamers, add the dimensional version you want – to CIP spec or to CIP minimum. For pilot bushings, state the matching reamer.

How do I enquire about gunsmithing tools at HANZ Arms?

You can reach HANZ Arms via the contact page on our website. Briefly describe which tool you need for which caliber. With the full caliber designation and the version you want, your enquiry can be assigned unambiguously.

Can I ask a question about an existing HANZ reamer?

Yes. Get in touch via our contact page. Give the caliber and the existing tool version. Relating it to the existing tool helps us answer your question precisely.



Gunsmithing tools

Looking for a chamber reamer for your caliber?

Tell us the tool and version you need. We use our reamers ourselves in our workshop and answer your enquiry from that hands-on experience.

Call Enquire ↗